158TS12153
Note:
1. ALL MARKINGS TO BE PER
INTERMATIC APPROVED
ARTWORK.
APPROVED MA
TERIAL:
WHITE VINYL W/PERMANENT PRESSURE
SENSITIVE ADHESIVE BACKING.
DR: SRB 4/21/2005 ITEM PART NUMBER DESCRIPTION QTY
ORIG:
INTERMATIC INCORPORATED
CHKD: JAP 4/21/2005
SCALE: FULL
NAME:
INST SHT - DOOR, T101R201, ENG.
APPROVED MATL: SEE APPROVED MATERIAL
1 RELEASED TO ELEC. DATA T101R201 JAP 4/21/2005 FINISH: BLACK PRINTING INK
LET REVISION DATE/BY MODEL
SUPERSEDES
HEAT TREAT
+1/32
3 7/8
TOOL
T
OL:
BOXED
T
OLERANCES
ARE FOR LIFE-OF-TOOL DEVIATION ONLY.
DO NOT USE FOR RE-TOOLING.
DIM TOL. : DECIMALS (UNLESS OTHERWISE SPECIFIED) - TWO PLACE (.00)
+
.015 - THREE PLACE (.000)
+
.005
ANGLES
+
30 MINUTES - ALL DIMENSIONS MUST BE MET BEFORE PLATING.
R (OPTIONAL)
D17
+1/32
6 3/4
SEE B/M FOR ALL PART NUMBERS & QUANTITIES
MODEL: T101R201
HYDRO-KING 2 CIRCUIT TIME SWITCH
IN TYPE 3R DUSTPROOF RAINPROOF ENCLOSURE, SUITABLE FOR POOL
E
QUIPMENT CONTROL IF INSTALLED 5 FT. OR MORE FROM EDGE OF POOL.
F
ILTER CIRCUIT SINGLE POLE SINGLE THROW (SPST)
40 AMP. RESISTIVE, INDUCTIVE TUNGSTEN OR
1000V.A. PILOT DUTY -120/208/240 VOLT AC,
2 H.P. (24 FLA) - 120 V. AC; 5 H.P. (28 FLA) - 240V. AC
HEATER CONTROL CIRCUIT: 10 AMP 125 VOLTS A C MAX
CLOCK MOTOR: 110-125V. 60 HZ.
WIRING INSTRUCTIONS: To wire switch follow diagram above. Use solid or strand
COPPER only wire with insulation to suit installation. See gauge selection table for
normal service applications. To make power connections remove 1/2 inch of insula-
tion from wire ends. Insert bare ends of wire under the pressure plate of terminals.
Use 3/16 or larger screwdriver to tighten terminal screws firmly. (25 lb-in minimum).
REPLACE INSULATOR BEFORE TURNING ON ELECTRICITY.
PROGRAMMING INSTRUCTIONS
• TO SET “ON” AND “OFF” TIMES:
Hold trippers
against edge of CLOCK-DIAL, pointing to time (AM or
PM) when ON and OFF operations are desired,
tighten tripper screws firmly. For additional tripper pairs
on CLOCK-DIAL order 156T1978A.
• TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward.
Turn in either direction and align the exact time-of-day
on the CLOCK-DIAL (time now, when switch is put into
operation) to TIME POINTER.
DO NOT MOVE POINTER.
OPERATING INSTRUCTIONS
• TO OPERATE SWITCH MANUALLY:
Move MANUAL
LEVER below CLOCK-DIAL left or right as indicated by
arrows. This will not effect next operation.
CAUTION: You must turn heater off at least 15 minutes before
manually turning off filter system.
• IN CASE OF POWER FAILURE, reset CLOCK-DIAL to
proper time-of-day. See programming instructions.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
158TS12153
C
LOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO
ORDER REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.
C
LOCK
MOTOR
W
IRING
DIAGRAM
120V
SUPPLY
T
O
L
OADS
N
EUT
LINE
A
2
1
CLOCK
DIAL
TIME
POINTER
OFF
TRIPPER
MANUAL
LEVER
ON
TRIPPER
MINIMUM
COPPER
WIRE SIZE
(AWG)
MAX.
LOAD
(AMP)
MIN.
INSUL-
ATION
TEMP (
°
C)
75
°
INSULATION MAX. MOTOR
LOAD (HP)
SINGLE PHASE
120V 240V
14
12
10
8
15
20
30
40
60
60
60
75
1/2
1
2
2
2 1/2
3
5
PRESSURE PLATE
TERMINAL
SCREW
MAKE SURE WIRE
INSULATION CLEARS
P
RESSURE PLATE
3 PHASE
240V 240V
N/A
N/A
LR3730
FIGURE 1
GND
T
O
HEATER
}
(1 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales